I-Low Pim 7/16 Din Owesilisa kuya ku-4.3-10 Adaptha Wesilisa
Ama-adapt akhiqizwa nge-Telsto Development Co, limited limited ahlukahlukene ahlukahlukene okucushwa okuhlukahlukene okufana nochungechunge noma phakathi kochungechunge oluchungechungeni, oluqondile noma oluhleliwe futhi amanye anezici zePanel Mount.
Zihlukaniswa ngokwezicelo zayo ezihlosiwe ezihlosiwe zazo zidinga izakhiwo zayo ezithile. Kunamaqembu amane amakhulu akhonjwa ngekhodi yombala kule khathalogu: okujwayelekile, ukunemba, ukuguquguquka okuningana okulandelanayo (i-PIM) kanye ne-adaptha esheshayo.
I-Telsto RF Adapter inobubanzi obuvame kakhulu be-DC-3 GHZ, inikeza ukusebenza okuhle kwe-VSWR kanye nokuguqulwa okuphansi kwe-Passive Movie ≤-PIM3 ≤-155DBC (2 × 20W)}. Lokhu kwenza kubekelwe kahle ukusetshenziswa eziteshini ezisesisekelo samaselula, kwasatshalaliswa izinhlelo ze-antenna (DAS) nezinhlelo zokusebenza zeselula ezincane.
| Umphumela | Ukufanisa | Ingxenye No. |
| I-adaptha ye-Rf | 4.3-10 abesifazane ku-DIN GEDER ADAPTER | Tel-4310f.Dinf-at |
| 4.3-10 Owesifazane ku-DIN MODE MADER ADAPTER | Tel-4310f.Dinm-at | |
| 4.3-10 Owesifazane ku-NO FLAST ADAPTER | Tel-4310f.nm-at | |
| 4.3-10 Owesilisa oya e-Adapter Yesilisa | Tel-4310m.Dinf-at | |
| 4.3-10 Owesilisa ukuze ad den sapter wesilisa | Tel-4310m.Dinm-at | |
| 4.3-10 Owesilisa kuya ku-N Owesifazane Adaptha | Tel-4310m.nf-at | |
| I-DIN Owesifazane ku-Din Male Angle Adapter | Tel-dinf.dinma-at | |
| N Owesifazane oya e-Din Male Adapter | Tel-nf.dinm-at | |
| N Owesifazane ku-A e-adaptha lowesifazane | Tel-nf.nf-at | |
| N owesilisa oya e-adaptha ye-DIN | Tel-nm.dinf-at | |
| N owesilisa oya e-Din Male Adapter | Tel-nm.dinm-at | |
| N owesilisa kuya ku-adaptha lowesifazane | Tel-nm.nf-at | |
| N owesilisa kuya ku-a adaptha abesilisa | Tel-nm.nma.at | |
| N owesilisa kuya ku-adaptha yabesilisa | Tel-nm.nm-at | |
| 4.3-10 abesifazane kuya ku-4.3-10 abesilisa angle angle arapter | Tel-4310f.4310ma-at | |
| I-DIN Owesifazane ku-Din Male Angle RF Adapter | Tel-dinf.dinma-at | |
| N Owesifazane ngakwesokunene i-angle ye-n fem adaptha ye-r | Tel-nfa.nf-at | |
| N owesilisa kuya ku-4.3-10 adaptha abesifazane | Tel-nm.4310f-at | |
| N owesilisa kuya ku-a adaptha angela abesifazane | Tel-nm.nfa-at |
Okuhlobene
Imodeli:Tel-4310m.Dinm-at
Ukufanisa
4.3-10 Owesilisa ukuze ad den sapter wesilisa
| Izinto ezibonakalayo kanye nethanga | |
| Ukuxhumana kwesikhungo | I-Brass / Isiliva Plating |
| Umshini wenulati | I-PTFE |
| Umzimba nomphakathi wangaphandle | I-Brass / Alloy Plated nge-Tri-Alloy |
| Gassela | I-silicon irabha |
| Izici zikagesi | |
| Izici Ukuvikelwa | 50 ohm |
| Ububanzi bokuvama | Dc ~ 3 ghz |
| Ukumelana nokufakelwa | ≥5000MM |
| Amandla we-Dielectric | ≥2500 v rms |
| Isikhungo Sokuxhumana Center | ≤33.0 mω |
| Ukumelana Kwangaphandle Ukumelana | ≤2.0 mω |
| Ukulahleka kokufaka | ≤0.3DB@3zzz |
| Vswr | ≤1.1@b-3.0hzz |
| Ububanzi bokushisa | -40 ~ 85 ℃ |
| I-PIM DBC (2 × 20W) | ≤-160 DBC (2 × 20W) |
| -Ngenamampuloso | IP67 |
Imiyalo yokufaka ye-N noma engu-7/16 noma i-4310 1/2 "ikhebula eliguquguqukayo
Ukwakheka kwesixhumi: (Fig1)
A. Front Nut
B. Back Nut
C. gasket
Ubukhulu bokuhlunga bukhonjiswe umdwebo (Fig2), ukunakwa kufanele kukhokhwe ngenkathi kuhlazeka:
1. Ingaphezulu lokugcina lomqhubi wangaphakathi kufanele lihlazwe.
2. Susa ukungcola okufana nesilinganiso sethusi kanye ne-burr endaweni yokugcina yekhebula.
Ukuhlangana kwengxenye yokubopha uphawu
Ukuhlangana ne-nut emuva (Fig3).
Hlanganisa i-Nut yangaphambili nangasemuva ngokushaya njengoba kukhonjisiwe ngumdwebo (amakhiwane (5)
1. Ngaphambi kokushaya, ufake ungqimba lokugcoba amafutha ku-O-ring.
2 Skrola phansi umzimba omkhulu wegobolondo lomzimba wegobolondo emuva usebenzisa i-monkey wrench. Ukubuthana sekuqediwe.
